Mobile

• Mobile module: 4G+ (LTE-A) – Cat 6 up to 300 Mbps, 3G – Up to 42 Mbps
• Status: Signal strength, SINR, RSRP, RSRQ, Bytes sent/received, connected band, carrier aggregation, IMSI, ICCID
• SMS: SMS status, SMS configuration, send/read SMS via HTTP POST/GET, Email to SMS, SMS to Email, SMS to HTTP, SMS to SMS, SMS auto reply
• USSD: Supports sending and reading Unstructured Supplementary Service Data messages
• Black/White list: Operator black/white list
• Multiple PDN: Possibility to use different PDNs for multiple network access and services
• Band management: Band lock, Used band status display
• APN: Auto APN
• Bridge mode: Direct connection (bridge) between mobile ISP and device on LAN

Wireless

• Wireless mode: 2.4 GHz (802.11 b/g/n, 2x2 MIMO), 5 GHz (802.11 ac, 1x1 MIMO), Access Point (AP), Station (STA)
• WiFi security: WPA3-EAP, WPA3-SAE, WPA2-Enterprise-PEAP, WPA2-PSK, WEP; AES-CCMP, TKIP, Auto Cipher modes, client separation
• ESSID: ESSID stealth mode
• Wireless Hotspot: Captive portal (Hotspot), internal/external Radius server, SMS OTP, MAC auth, built in customisable landing page, walled garden
• Wireless mesh/roaming: Wireless mesh (802.11s), fast roaming (802.11r)

Ethernet

• WAN: 1 x WAN port (can be configured as LAN) 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover
• LAN: 1 x LAN port, 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIX crossover

Network

• Routing: Static routes, Dynamic routes
• Network protocols: TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet client, SNMP, MQTT, Wake on LAN (WOL)
• Connection monitoring: Ping Reboot, Wget reboot, Periodic Reboot, LCP and ICMP for link inspection
• Firewall: Port forwards, traffic rules, NAT rules, custom rules
• DHCP: Static and dynamic IP allocation, DHCP Relay, Relayd
• QoS / Smart Queue Management (SQM): Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e
• DDNS: Supported > 25 service providers, others can be configured manually
• Network backup: Mobile, Wired and WiFi WAN options, each of which can be used as an automatic Failover
• Load balancing: Balance internet traffic over multiple WAN connections
• SSHFS: Possibility to mount remote file system via SSH protocol

Security

• Authetication: Pre-shared key, digital certificates, X.509 certificates
• Firewall: Pre-configured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T
• Attack prevention: DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)
• VLAN: Tag based VLAN separation
• Mobile quota control: Custom data limits for SIM card (SIM card not included)
• WEB filter: Blacklist for blocking out unwanted websites, Whitelist for specifying allowed sites only
• Access control: Flexible access control of TCP, UDP, ICMP packets, MAC address filter

VPN

• OpenVPN: Multiple clients and a server can run simultaneously, 12 encryption methods
• OpenVPN Encryption: DES-CBC, RC2-CBC, DES-EDE-CBC, DES-EDE3-CBC, DESX-CBC, BF-CBC, RC2-40-CBC, CAST5-CBC, RC2-64-CBC, AES-128-CBC, AES-192-CBC, AES-256-CBC
• IPSec: IKEv1, IKEv2, with 5 encryption methods for IPsec (DES, 3DES, AES128, AES192, AES256)
• GRE: GRE tunnel
• PPTP, L2TP: Client/Server instances can run simultaneously, L2TPv3 support
• Stunnel: Proxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s code
• DMVPN: Method of building scalable IPsec VPNs
• SSTP: SSTP client instance support
• ZeroTier: ZeroTier VPN client support
• WireGuard: WireGuard VPN client and server support

MODBUS TCP Slave

• ID filtering: Respond to one ID in range [1;255] or any
• Allow remote access: Allow access through WAN
• Custom registers: MODBUS TCP custom register block, which allows to read/write to a file inside the router, and can be used to extend MODBUS TCP slave functionality

MODBUS TCP Master

• Supported functions: 01, 02, 03, 04, 05, 06, 15, 16
• Supported data formats: 8 bit: INT, UINT; 16 bit: INT, UINT (MSB or LSB first); 32 bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII

MQTT Gateway

• Gateway: Allows sending commands and receiving data from MODBUS Master trough MQTT broker

DNP3

• Supported modes: TCP Master, DNP3 Outstation

Data to Server

• Protocols: HTTP(S), MQTT, Azure MQTT, Kinesis

Monitoring & Management

• WEB UI: HTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, event log, system log, kernel log
• FOTA: Firmware update from server, automatic notification
• SSH: SSH (v1, v2)
• SMS: SMS status, SMS configuration, send/read SMS via HTTP POST/GET
• Call: Reboot, Status, Mobile data on/off, Output on/off
• TR-069: OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem
• MQTT: MQTT Broker, MQTT publisher
• SNMP: SNMP (v1, v2, v3), SNMP trap
• JSON-RPC: Management API over HTTP/HTTPS
• MODBUS: MODBUS TCP status/control
• RMS: Teltonika Remote Management System (RMS)

IoT Platforms

• Clouds of things: Allows monitoring of: Device data, Mobile data, Network info, Availability
• ThingWorx: Allows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network Type
• Cumulocity: Allows monitoring of: Device Model, Revision and Serial Number, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength, WAN Type and IP
• Azure IoT Hub: Can send device IP, Number of bytes send/received, Mobile connection state, Network link state, IMEI, ICCID, Model, Manufacturer, Serial, Revision, IMSI, SIM State, PIN state, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, Operator, Operator number, Connection type, Temperature, PIN count to Azure IoT Hub server

System Characteristics

• CPU: QCA9531, MIPS 24kc, 650 MHz
• RAM: 128 MB, DDR2
• FLASH storage: 16 MB, SPI Flash
• Firmware / Configuration
• WEB UI: Update FW from file, check FW on server, configuration profiles, configuration backup
• FOTA: Update FW/configuration from server
• RMS: Update FW/configuration for multiple devices at once
• Keep settings: Update FW without losing current configuration

Power

• Connector: 4 pin industrial DC power socket
• Input voltage range: 9 - 30 VDC, reverse polarity protection, voltage surge/transient protection
• Power consumption: 3.7 W average, 9.3 W max
• Physical Interfaces (Ports, LEDs, Antennas, Buttons, SIM)
• Ethernet: 2 x RJ45 ports, 10/100 Mbps
• Status LEDs: 1 x Internet, 1 x WiFi, 3 x Mobile connection strength, 2 x Ethernet status
• SIM (card not included): 1 x SIM slots (Mini SIM - 2FF), 1.8 V/3 V, external SIM holder
• Antenna: 2 x SMA for LTE, 2 x Internal for 2.4 GHz WiFi, 1 x Internal for 5 GHz WiFi
• Power: 1 x 4 pin DC connector
• WPS: WPS activation button
• WiFi On/Off: WiFi enable/disable button
• Reset: Reboot/User default reset/Factory reset button

Physical Specification

• Casing material: Plastic housing with aluminium screws and heatsink
• Dimensions (W x H x D): 150 x 37 x 105 mm
• Weight: 376 g
• Mounting options: Flat surface placement

Operating Environment

• Operating temperature: -40°C to 75°C
• Operating humidity: 10% to 90% non-condensing

Package Contents

• 1 x TCR100
• 1 x 18W PSU
• 2 x LTE antennas (swivel, SMA male)
• 1 x Ethernet cable (1.5m)
• 1 x SIM Adapter kit
• 1 x QSG (Quick Start Guide)
• 1 x RMS Flyer