Ubiquiti UniFi Access Reader Technical Specifications

UA-Hub-Door - Mechanical

• Dimensions: 174.9 x 126 x 32.9 mm (6.9 x 5 x 1.3")
• Weight: 363 g (12.8 oz)
• Enclosure material: Polycarbonate
• Mounting material: Polycarbonate

UA-Hub-Door - Hardware

• Networking interface: (5) 10/100/1000 Base-T
• Power method: PoE++, UL 294 Power-limited Class 2 PSU, UL 60950/62368 LPS/PS2 PSU
• Max. power consumption: Without PoE output: 30W, With PoE output: 50W
• PoE input: 50V DC, 1A
• PoE output: PoE passthrough, (4) PoE, 50V DC, total 20W
• Button: (1) Factory-reset
• LEDs: System: white/blue, Output relays: white, Digital input: Request to exit/request to enter/remote release/door position sensor
• Dry output relay: Lock: 30V DC, 1A, Aux: 30V DC, 1A
• Powered output relay: Lock: 12V DC, 1A, Aux: 12V DC, 0.33A
• Operating environment: Indoor use only
• Operating temperature: 0 to 40°C (32 to 104°F)
• Operating humidity: 5 to 95% noncondensing
• UL 294 level: Destructive attack: Level I, Line security: Level I, Endurance: Level I, Standby power: Level I
• UL 294 statement: Compliance with IEEE 802.3 (at or af) specifications was not verified as part of UL 294. The equipment is intended to comply with the section of the National Electrical Code, ANSI/NFPA 70, Article 725.121, Power Sources for Class 2 and Class 3 Circuits.
• CAN/ULC-60839-11-1 Grade: Grade assignment: 1
• Certifications: CE, FCC, IC, UL 294, CAN/ULC-60839-11-1
• Document number, and issue date and/or revision level: UA-Hub-Door002, V01

UA-Hub-Door - Wiring Information

• Typical installation (Shielded):
• DC power input: Belden 8750 18 AWG 2 conductor (30.5 m/100 ft)
• Door position switch: Belden 8750 18 AWG 2 conductor (152.5 m/500 ft)
• Request to exit: Belden 8750 18 AWG 2 (152.5 m/500 ft)
• Wiring gauge requirements (AWG):
  • Total length to device
  • Output load current at 12V DC
  • 6.1 m (20 ft): 22, 22, 22, 18
  • 15.2 m (50 ft): 22, 22, 22, 18
  • 30.5 m (100 ft): 22, 22, 18, 18
• PoE cabling requirements: The minimal conductor gauge permitted to connect between the PSE or power injector and the PD shall be 24 AWG (0.21 mm2) for horizontal or riser cable.

UA-Hub-Door - LEDs

• PoE in: Steady blue: Adopted/device is ready, Steady white: Pending adoption, Blinking white/blue: Upgrading firmware
• PoE out: Off: Not connected or no data link, Steady blue: Connected and data link on

UA-G2 - Mechanical

• Dimensions: 93 x 40 x 36.5 mm (3.7 x 1.6 x 1.4")
• Weight: 82 g (2.9 oz)
• Enclosure material: Polycarbonate, glass
• Mounting: In wall, gang box
• Weatherproofing: IP55

UA-G2 - Hardware

• Networking interface: (1) 10/100 MbE RJ45 port
• Connectivity: BLE 4.1
• Power method: PoE
• Supported voltage range: 48V DC
• Max. power consumption: 5W
• ESD/EMP protection: Air: ±15kV, contact: ±8kV
• Sensors: Proximity sensor
• Speaker: (1) 8 ohm, 0.7W
• LEDs: R/G/B/W
• Button: (1) Factory-reset
• NFC frequency: 13.56 MHz
• NFC read range: < 30 mm
• NFC standards: ISO 14443A, 14443B, 15693
• NFC technology: NFC Tag 1,2,3,4,5, MIFARE Classic, MIFAREPlus, MIFARE Ultralight, MIFARE DESFire
• Operating temperature: -30 to 45°C (-22 to 113°F)
• Operating humidity: 5 to 90% noncondensing
• Certifications: CE, FCC, IC

UA-Card - Mechanical

• Dimensions: 85.6 x 53.98 x 0.84 mm (3.37 x 2.13 x 0.03")
• Weight: 5 g (0.18 oz)
• Format: ISO 7810 ID-1

UA-Card - NFC

• NFC frequency: 13.56 MHz
• NFC technology: ISO/IEC 14443 Type A, MIFARE DESFire, UniFi Access Proprietary Security Protocol