Ubiquiti Elevator Starter Kit Technical Specifications

UA-Hub-Elevator

• Mechanical
• Dimensions: 129.3 x 244.7 x 33.6 mm (5.1 x 9.6 x 1.3")
• Weight: 537 g (1.2 lb)
• Enclosure material: Polycarbonate
• Mounting material: Polycarbonate
• Hardware
• Networking interface: (4) 10/100/1000 Base-T
• Management interface: (1) 10/100/1000 Base-T
• Power method: PoE++
• Max. power consumption: 7W (Without PoE output)
• PoE input: (1) PoE++, 50V DC, 1.2A
• PoE output: PoE passthrough, (4) PoE, 50V DC, total 42W
• ESD/EMP protection: Air: ±8kV, contact: ±4kV
• Digital input: (6) Car position; Up/down/stop/full/door open/door close
• (1) Emergency
• Outputs: (18) Relays, Rating 30V DC/2A
• LEDs: System: white/blue/red, Output relays: white
• Buttons: (1) Factory-reset
• Terminal blocks
• Operating temperature: -10 to 40° C (14 to 104° F)
• Operating humidity: 5 to 95% noncondensing
• Certifications: CE, FCC, IC

UACC-Extender-2Wire-Tx/Rx

• Mechanical
• Dimensions: 40 x 105 x 25 mm (1.6 x 4.1 x 1")
• Weight: PoE in: 77 g (2.7 oz), PoE out: 79 g (2.8 oz)
• Enclosure material: Polycarbonate
• Mounting material: Polycarbonate
• Hardware
• Networking interface: (1) 10/100 MbE, (1) Homeplug AV
• Management interface: (1) 10/100 MbE
• Power method: PoE++
• Max. power consumption: 3W (Without PoE output)
• PoE input: (1) PoE++, 50V DC, Max. 1.2A
• PoE output: (1) PoE+, 48V DC, 0.72A
• ESD/EMP protection: Air: ±8kV, contact: ±4kV
• LED: White
• Operating temperature: -10 to 40° C (14 to 104° F)
• Operating humidity: 5 to 95% noncondensing
• Certifications: CE, FCC, IC

UA-G2

• Mechanical
• Dimensions: 93 x 40 x 36.5 mm (3.7 x 1.6 x 1.4")
• Weight: 82 g (2.9 oz)
• Enclosure material: Polycarbonate, glass
• Mounting: In wall, gang box
• Weatherproofing: IP55
• Hardware
• Networking interface: (1) 10/100 MbE RJ45 port
• Connectivity: BLE 4.1
• Power method: PoE
• UL 294 Power-limited Class 2 PSU
• UL 60950-1/62368-1 LPS/PS2 PSU
• Supported voltage range: 48V DC
• Max. power consumption: 5W
• ESD/EMP protection: Air: ±15kV, contact: ±8kV
• Sensors: Proximity sensor
• Speaker: (1) 8 ohm, 0.7W
• LEDs: R/G/B/W
• Button: (1) Factory-reset
• NFC frequency: 13.56 MHz
• NFC read range: < 30 mm
• NFC standards: ISO 14443A, 14443B, 15693
• NFC technology: NFC Tag 1,2,3,4,5; MIFARE Classic, MIFAREPlus, MIFARE Ultralight, MIFARE DESFire
• Operating environment: Outdoor use
• Operating temperature: -30 to 45° C (-22 to 113° F)
• Operating humidity: 5 to 90% noncondensing
• Software Information
• The software version of a product can be checked at
• UL 294 Level
• Destructive attack: Level I
• Line security: Level I
• Endurance: Level I
• Standby power: Level I
• UL 294 Statement
• Compliance with IEEE 802.3 specifications was not verified as part of UL 294.
• The equipment is intended to comply with the section of the National Electrical Code, ANSI/NFPA 70, Article 725.121, Power Sources for Class 2 and Class 3 Circuits.
• PoE Cabling Requirements
• Cable 5e cabling is the minimum performance category recommended.
• The performance category utilized should match the transmission speed required at the installation site.
• The minimal conductor gauge permitted to connect between the PSE or power injector and the PD shall be 26 AWG (0.13 mm2) for patch cords; 24 AWG (0.21 mm2) for horizontal or riser cable.
• CAN/ULC-60839-11-1 Grade
• Grade assignment: I
• Certifications
• CE, FCC, IC, UL 294, CAN/ULC-60839-11-1
• Document Number, and Issue Date and/or Revision Level
• UA-G2/UA-G2-Black, V02
• LED
• System: Steady blue: Adopted/device is ready
• Steady white: Pending adoption
• Blinking white/blue: Upgrading firmware
• Strobing red: Emergency lockdown

UA-Card

• Mechanical
• Dimensions: 85.6 x 54 x 0.8 mm (3.4 x 2.1 x 0.03")
• Weight: 5 g (0.18 oz)
• Format: ISO 7810 ID-1
• NFC frequency: 13.56 MHz
• NFC technology: ISO/IEC 14443 Type A; MIFARE DESFire; UniFi Access Proprietary Security Protocol